02 Roller Landed in My Lap!

808Bill
NG (Second 100 Outposters!)
Posts: 189
Joined: Fri May 18, 2018 6:36 am

Re: 02 Roller Landed in My Lap!

Post by 808Bill » Sun Jul 29, 2018 7:10 am

32wildbilly wrote:
Fri Jul 27, 2018 6:26 am
808Bill wrote:
Fri Jul 27, 2018 5:59 am
PICTURE
You are...very funny! :roll:
I have more, would you like to see them? :lol:

User avatar
32wildbilly
OG (First 100 Outposters!)
Posts: 1590
Joined: Sat Jan 06, 2018 2:46 pm
Location: Kneebraska

Re: 02 Roller Landed in My Lap!

Post by 32wildbilly » Sun Jul 29, 2018 12:33 pm

808Bill wrote:
Sun Jul 29, 2018 7:10 am
32wildbilly wrote:
Fri Jul 27, 2018 6:26 am


You are...very funny! :roll:
I have more, would you like to see them? :lol:
giphy-17.gif
giphy-17.gif (1.35 MiB) Viewed 226 times

808Bill
NG (Second 100 Outposters!)
Posts: 189
Joined: Fri May 18, 2018 6:36 am

Re: 02 Roller Landed in My Lap!

Post by 808Bill » Sun Jul 29, 2018 5:11 pm

Replaced my lower rear Tract Rods (aka Toe Control) and discovered a cracked bushing. Unseen unless you remove them.
I wonder how many others are driving around like this?
IMG_0652.JPG
Attachments
IMG_0649.JPG

808Bill
NG (Second 100 Outposters!)
Posts: 189
Joined: Fri May 18, 2018 6:36 am

Re: 02 Roller Landed in My Lap!

Post by 808Bill » Fri Aug 03, 2018 7:43 am

Motor is on island and ready for pick up! Now if only Hurricane Hector would go away...

User avatar
32wildbilly
OG (First 100 Outposters!)
Posts: 1590
Joined: Sat Jan 06, 2018 2:46 pm
Location: Kneebraska

Re: 02 Roller Landed in My Lap!

Post by 32wildbilly » Fri Aug 03, 2018 8:30 am

808Bill wrote:
Fri Aug 03, 2018 7:43 am
Motor is on island and ready for pick up! Now if only Hurricane Hector would go away...
It is early but the track projection appears to be curving a little more towards the WSW rather than due West!

808Bill
NG (Second 100 Outposters!)
Posts: 189
Joined: Fri May 18, 2018 6:36 am

Re: 02 Roller Landed in My Lap!

Post by 808Bill » Fri Aug 03, 2018 9:05 am

Just like Iwa and Iniki, then they made a hard right to Kauai...Direct hit!

User avatar
Groovzilla
OG (First 100 Outposters!)
Posts: 124
Joined: Wed Jan 31, 2018 11:03 am
Location: Seattle, Wa.

Re: 02 Roller Landed in My Lap!

Post by Groovzilla » Fri Aug 03, 2018 3:33 pm

It was always fun parting out 356's when they were rusted beyond repair. Of course those parts are worth more than jewelry and there was great fun and profit. Those were the days.....(Edith and Archie singing in background)

Would be fun to part out a 996 - Just taking your time, organizing them and do some ebay/forum sales - I'd guestimate close to $12K in parts sales - Hell the engine alone should fetch $2-3K for all the usable parts?

Lots of work but fun stuff
2005 997 S - Atlas grey w/Full black leather

808Bill
NG (Second 100 Outposters!)
Posts: 189
Joined: Fri May 18, 2018 6:36 am

Re: 02 Roller Landed in My Lap!

Post by 808Bill » Sun Aug 05, 2018 2:47 pm

Picked up the motor and pulled the flywheel to see this...I had already planned on replacing the IMSB and RMS.
My question is how does one determine if it's a non servicable bearing? Motor is an AT built in 05. 22mm nut.
Attachments
IMG_0668.JPG
IMG_0656.JPG

User avatar
gnat
OG (First 100 Outposters!)
Posts: 1303
Joined: Sat Jan 06, 2018 6:54 am
Location: If you knew, you'd move

Re: 02 Roller Landed in My Lap!

Post by gnat » Sun Aug 05, 2018 3:25 pm

Big nut = big pain in the ass

You gotta crack the case to do it right. There is an option out there to drill it out, but that just seems like a horrible idea to me (you going to bet that motor against being damn sure no debris gets left in the oil area?).

808Bill
NG (Second 100 Outposters!)
Posts: 189
Joined: Fri May 18, 2018 6:36 am

Re: 02 Roller Landed in My Lap!

Post by 808Bill » Sun Aug 05, 2018 4:16 pm

That's what I thought, I'll just have to pull the flange and pop off the oil seal and have a look. I sure hope the RMS is the source of oil and not the IMSB flange.

Who's got the cam locking tools to loan/rent?

Post Reply