Things you will need:
Ratchet Straps 2x or 3x
Teflon baking Sheets (flexible)
Additional person
Painters tape
So with the help of a friend of mine I was able to get the roll bar in without taking the mirror off, while it took some care full massaging this should provide some tricks to make it easier to install your 901 RSS bar.
First step is to remove seats and center console to free up room. Helps to do this outside or in a garage with enough room to totally open the doors. Using cardboard or some blankets on the ground goes a long way as you will be kneeling a lot to do this.
At the time my old garage barn did not have enough space to open the doors fully inside so outside it was.
Make sure to use painters tape on the rockers/door sills to prevent damage
Tilting the bar into position
Using the ratchet straps to pull the legs in and also to pull the strap up to clear the e-brake and shifter cables helps a lot. Using the teflon baking sheets on the top of the bar between it and head liner helps prevent damage to the headliner.
Bar in
Seats and harnesses back in
DIY 901 RSS Roll Bar Install 996 Turbo
- TheDeckMan
- OG (First 100 Outposters!)
- Posts: 345
- Joined: Fri Feb 16, 2018 8:52 am
- Location: Masshole behind communist lines
- Contact:
DIY 901 RSS Roll Bar Install 996 Turbo
996TT - Widowmaker Project -RWD, UMW Tune, H&R RSS, Phenix Engineering Control Arms/LCA's, GT3 6 Pistons, SpeedTech 3" X-Pipe, Ported Headers, 997 GT3 Shifter, GT3 Buckets, GT2 Clutch/PP, GT2RS IC's, RSS Roll Bar, GT3 Brake Ducts, Joe Toth Aero/Ducts, Champion Thrust Arms
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/
Re: DIY 901 RSS Roll Bar Install 996 Turbo
How you like? Can you feel the added rigidity?
- TheDeckMan
- OG (First 100 Outposters!)
- Posts: 345
- Joined: Fri Feb 16, 2018 8:52 am
- Location: Masshole behind communist lines
- Contact:
Re: DIY 901 RSS Roll Bar Install 996 Turbo
Little firmer, not super crazy but you do notice it for sure.
996TT - Widowmaker Project -RWD, UMW Tune, H&R RSS, Phenix Engineering Control Arms/LCA's, GT3 6 Pistons, SpeedTech 3" X-Pipe, Ported Headers, 997 GT3 Shifter, GT3 Buckets, GT2 Clutch/PP, GT2RS IC's, RSS Roll Bar, GT3 Brake Ducts, Joe Toth Aero/Ducts, Champion Thrust Arms
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/
Re: DIY 901 RSS Roll Bar Install 996 Turbo
Put the same bar in mine around the same time, I was so stuck trying to get the bar to rotate back until I tried the cardboard trick between the roll bar and the headliner. Worked like a champ
:: '03 996 C2 :: Daily Driven - Enjoyed Properly
- TheDeckMan
- OG (First 100 Outposters!)
- Posts: 345
- Joined: Fri Feb 16, 2018 8:52 am
- Location: Masshole behind communist lines
- Contact:
Re: DIY 901 RSS Roll Bar Install 996 Turbo
Great to hear the trick worked for someone else!
996TT - Widowmaker Project -RWD, UMW Tune, H&R RSS, Phenix Engineering Control Arms/LCA's, GT3 6 Pistons, SpeedTech 3" X-Pipe, Ported Headers, 997 GT3 Shifter, GT3 Buckets, GT2 Clutch/PP, GT2RS IC's, RSS Roll Bar, GT3 Brake Ducts, Joe Toth Aero/Ducts, Champion Thrust Arms
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/
- TheDeckMan
- OG (First 100 Outposters!)
- Posts: 345
- Joined: Fri Feb 16, 2018 8:52 am
- Location: Masshole behind communist lines
- Contact:
Re: DIY 901 RSS Roll Bar Install 996 Turbo
996TT - Widowmaker Project -RWD, UMW Tune, H&R RSS, Phenix Engineering Control Arms/LCA's, GT3 6 Pistons, SpeedTech 3" X-Pipe, Ported Headers, 997 GT3 Shifter, GT3 Buckets, GT2 Clutch/PP, GT2RS IC's, RSS Roll Bar, GT3 Brake Ducts, Joe Toth Aero/Ducts, Champion Thrust Arms
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/
- TheDeckMan
- OG (First 100 Outposters!)
- Posts: 345
- Joined: Fri Feb 16, 2018 8:52 am
- Location: Masshole behind communist lines
- Contact:
Re: DIY 901 RSS Roll Bar Install 996 Turbo
Great to hear the trick worked for someone else!
996TT - Widowmaker Project -RWD, UMW Tune, H&R RSS, Phenix Engineering Control Arms/LCA's, GT3 6 Pistons, SpeedTech 3" X-Pipe, Ported Headers, 997 GT3 Shifter, GT3 Buckets, GT2 Clutch/PP, GT2RS IC's, RSS Roll Bar, GT3 Brake Ducts, Joe Toth Aero/Ducts, Champion Thrust Arms
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/
997TT - LSD, Chrono , UMW Tune, DSC, Phenix Engineering Toe Links & LCA Bushings, Tubi Race, 3" eRams, 964RS Engine Mounts
Audi TT Track Car
Corrado SLC
https://phenixengineering.com/