Anyone know much about 3d printers?

User avatar
32wildbilly
Never gonna run around and desert you
Posts: 5758
Joined: Sat Jan 06, 2018 2:46 pm
Location: Kneebraska

Re: Anyone know much about 3d printers?

Post by 32wildbilly » Tue Jan 26, 2021 10:59 am

Ok so I know the point is it can be done with a "pen" which is cool. My question is what do you think is the estimate of weight and durability(asked by a guy who raced 1/8th scale nitro asphalt cars and 1/10th scale electric indoor cars) of this body.
gnat wrote: Tue Jan 26, 2021 10:16 am :shock: :shock: :shock: :shock:


Shorter version without weird Sponge Bob interludes...:
Never gonna make you cry...

User avatar
gnat
Power-drunk moderator
Posts: 4171
Joined: Sat Jan 06, 2018 6:54 am
Location: Lobby, VWGofA HQ

Re: Anyone know much about 3d printers?

Post by gnat » Tue Jan 26, 2021 11:07 am

32wildbilly wrote: Tue Jan 26, 2021 10:59 am Ok so I know the point is it can be done with a "pen" which is cool. My question is what do you think is the estimate of weight and durability(asked by a guy who raced 1/8th scale nitro asphalt cars and 1/10th scale electric indoor cars) of this body.
If I was driving, I think I lasted about 30 seconds before my first roll the other day when I took my 1/8 monster out for the first time in ages (Brushless 4S LiPo FTW!).

The Bondo probably helps with integrity, but one good hit and it's done. Definitely not practical, but really cool that he could do it with a 3D pen.

Interestingly, just yesterday I was looking at Blaze and the Monster Machines pics to see if I could figure out how to make a Blaze body for either my 1/8th or the oldest's 1/10th. The youngest is monster truck crazy at the moment and loves the Blaze Hot Wheels style trucks he took from his brother. I suck at modeling though :(

User avatar
5chn3ll
Six shots...or only five?
Posts: 4640
Joined: Fri Jan 05, 2018 4:35 pm

Re: Anyone know much about 3d printers?

Post by 5chn3ll » Wed Jan 27, 2021 2:15 pm

I have a couple of those 3D pens that print with PLA filament; I've always put them in the novelty category.

Like Gnat said, it's cool that he pulled that off with a pen. Any attempt I made would, as my dear ol' grandpa Theodore Roosevelt (not an OG - but still legit first and middle names) used to say, look like a bear's ass sewed up with a grapevine.

Understeer: You will hit the wall with the front end.
Oversteer: You will hit the wall with the rear end.
Horsepower: How hard you will hit the wall.
Torque: How far you will move the wall.

Gone hunting with Alec Baldwin and Dick Cheney. Back soon.

User avatar
FRUNKenstein
Curator Extraordinaire
Posts: 3938
Joined: Fri Jan 05, 2018 11:02 pm
Location: Wheat field, dammit, wheat!
Contact:

Re: Anyone know much about 3d printers?

Post by FRUNKenstein » Wed Jan 27, 2021 4:27 pm

Wow, here’s a really cool 3D printer project - worth a look:


https://www.google.com/search?sxsrf=ALe ... 61&bih=825
www.kansascityautomuseum.com
Current:
2002 996TT X50, Guards Red
1987 928S4, Guards Red
1987 951, Guards Red
1973 914 2.0 Bahia Red

2006 955S, Lapis Blue
Other toys:
1988 BMW 325i Cabriolet, Alpin Weiss
1987 Bertone X1/9, Verde Chiaro
Gone but not forgotten: 1975 914 2.0, Laguna Blue; 1999 996 C4 Aerokit Black; 1990 964 C2 Guards Red; 2006 955S Arctic Silver

User avatar
32wildbilly
Never gonna run around and desert you
Posts: 5758
Joined: Sat Jan 06, 2018 2:46 pm
Location: Kneebraska

Re: Anyone know much about 3d printers?

Post by 32wildbilly » Wed Jan 27, 2021 4:47 pm

I am NOT clicking on that link...
FRUNKenstein wrote: Wed Jan 27, 2021 4:27 pm Wow, here’s a really cool 3D printer project - worth a look:


https://www.google.com/search?sxsrf=ALe ... 61&bih=825
Never gonna make you cry...

User avatar
gnat
Power-drunk moderator
Posts: 4171
Joined: Sat Jan 06, 2018 6:54 am
Location: Lobby, VWGofA HQ

Re: Anyone know much about 3d printers?

Post by gnat » Sun Feb 07, 2021 12:59 pm

So we got some snow this morning and the oldest and I took our RC trucks out to have some fun. He got a bit big for himself, however, and rammed his 1:10 brushed truck into my 1:8 brushless which was probably doing 30mph at the time. I thought it was an accident, but he fessed up later that he was trying to hit me...

So this happened:
PXL_20210207_201400075.MP.jpg
PXL_20210207_201400075.MP.jpg (762.13 KiB) Viewed 1896 times
So some PETG and 2 hours on the printer produced:
PXL_20210207_202514353.MP.jpg
PXL_20210207_204620751.MP.jpg
PXL_20210207_204620751.MP.jpg (711.77 KiB) Viewed 1896 times
It's not going to hold up to significant abuse, but hopefully should last until the aluminum replacements show up later in the week.

User avatar
32wildbilly
Never gonna run around and desert you
Posts: 5758
Joined: Sat Jan 06, 2018 2:46 pm
Location: Kneebraska

Re: Anyone know much about 3d printers?

Post by 32wildbilly » Sun Feb 07, 2021 1:24 pm

Nicely done! Aluminum will break too...
gnat wrote: Sun Feb 07, 2021 12:59 pm So we got some snow this morning and the oldest and I took our RC trucks out to have some fun. He got a bit big for himself, however, and rammed his 1:10 brushed truck into my 1:8 brushless which was probably doing 30mph at the time. I thought it was an accident, but he fessed up later that he was trying to hit me...

It's not going to hold up to significant abuse, but hopefully should last until the aluminum replacements show up later in the week.
Never gonna make you cry...

User avatar
5chn3ll
Six shots...or only five?
Posts: 4640
Joined: Fri Jan 05, 2018 4:35 pm

Re: Anyone know much about 3d printers?

Post by 5chn3ll » Wed Feb 10, 2021 11:28 am

Any kind of composite over-wrap - epoxy with glass fiber or shredded CF - would make those things exponentially stronger. Maybe stronger (by mass) than aluminum...
gnat wrote: Sun Feb 07, 2021 12:59 pm It's not going to hold up to significant abuse, but hopefully should last until the aluminum replacements show up later in the week.

Understeer: You will hit the wall with the front end.
Oversteer: You will hit the wall with the rear end.
Horsepower: How hard you will hit the wall.
Torque: How far you will move the wall.

Gone hunting with Alec Baldwin and Dick Cheney. Back soon.

User avatar
Dr_Strangelove
Won't stay Banned
Posts: 1976
Joined: Wed Jan 17, 2018 2:46 pm
Location: Henderson, NV

Re: Anyone know much about 3d printers?

Post by Dr_Strangelove » Thu Feb 11, 2021 10:29 am

Woah that's cool gnat. What kind of scan tool do you use for the replacement? Or were the replacement schematics available online?
2003 Carrera: Dark Teal Metallic

User avatar
gnat
Power-drunk moderator
Posts: 4171
Joined: Sat Jan 06, 2018 6:54 am
Location: Lobby, VWGofA HQ

Re: Anyone know much about 3d printers?

Post by gnat » Thu Feb 11, 2021 10:53 am

Dr_Strangelove (whew!) wrote: Thu Feb 11, 2021 10:29 am Woah that's cool gnat. What kind of scan tool do you use for the replacement? Or were the replacement schematics available online?
Someone had already made the model and I just grabbed it of thingiverse.com.

I paid $30 for the aluminum replacements (came in yesterday even though I forgot to order them Sunday like I meant and Amazon said they'd arrive tomorrow) so I wouldn't have wasted the time modeling and testing.

Post Reply