Upgraded my shitty HF welder with an incrementally less shitty HF welder
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
Good comments. I have about 5 minutes on the new flux core welder; I definitely don’t have the settings dialed in yet...or the technique. That welder is a lot like my 996 - any performance issues are definitely the fault of the operator.
Understeer: You will hit the wall with the front end.
Oversteer: You will hit the wall with the rear end.
Horsepower: How hard you will hit the wall.
Torque: How far you will move the wall.
Gone hunting with Alec Baldwin and Dick Cheney. Back soon.
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
Those would clean up with a flap disc, but I was just using a wire wheel to knock off the slag last night. I’m going to cheat and pick up a can of anti-spatter spray...
Dr_Strangelove (whew!) wrote: ↑Thu Jul 16, 2020 9:29 am Are the little "sputters" around your welds discharged from the welder or is that a technique thing you need to clean up?
Understeer: You will hit the wall with the front end.
Oversteer: You will hit the wall with the rear end.
Horsepower: How hard you will hit the wall.
Torque: How far you will move the wall.
Gone hunting with Alec Baldwin and Dick Cheney. Back soon.
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
An angle grinder is a welder's best friend as it hides all by the worst mistakes5chn3ll wrote: ↑Thu Jul 16, 2020 1:48 pm Those would clean up with a flap disc, but I was just using a wire wheel to knock off the slag last night. I’m going to cheat and pick up a can of anti-spatter spray...
Dr_Strangelove (whew!) wrote: ↑Thu Jul 16, 2020 9:29 am Are the little "sputters" around your welds discharged from the welder or is that a technique thing you need to clean up?
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
Yeah...I was lazy last night and didn't pull out the grinders. I keep a flap disc on one and a death wheel on the other...
Wait, I thought spray paint was a welder's best friend.An angle grinder is a welder's best friend as it hides all by the worst mistakes
Understeer: You will hit the wall with the front end.
Oversteer: You will hit the wall with the rear end.
Horsepower: How hard you will hit the wall.
Torque: How far you will move the wall.
Gone hunting with Alec Baldwin and Dick Cheney. Back soon.
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
Just don't be like the geniuses in my welding class at Job Corps that thought it was great fun to stop a spinning angle grinder with their (gloved) hand. I'll leave the results to the imagination, but the lead asshole got what he deserved in the end and I got a good (if morbid) laugh at his expense.
- Dr_Strangelove
- Won't stay Banned
- Posts: 1990
- Joined: Wed Jan 17, 2018 2:46 pm
- Location: Henderson, NV
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
This is great stuff because I really would love to learn to weld. It's on my list and probably next. General wrenching and then advanced wrenching came first.
2003 Carrera: Dark Teal Metallic
- 32wildbilly
- Never gonna run around and desert you
- Posts: 5783
- Joined: Sat Jan 06, 2018 2:46 pm
- Location: Kneebraska
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
I know this is different than a angle grinder but Holy Shit!
NPPD employee impaled by rebar while clearing brush near Firth is now stable
A 46-year-old Lincoln man seriously injured in a workplace accident Thursday afternoon near Firth now was in stable condition on Friday morning, according to the Lancaster County Sheriff's Office.
Chief Deputy Todd Duncan said Roger Kempf, an employee with the Nebraska Public Power District, had been clearing brush from beneath power lines at David Drive and South 82nd Street when it happened at about 2:45 p.m.
He said one of Kemp's co-workers was operating a Cat Track Loader with a front-mounted disk grinder when the disk grinder struck a piece of rebar from an electric fence post at least 2 feet long that was concealed in the brush.
Duncan said the disk grinder launched the steel post and it flew about 60 yards, striking Kempf in the lower back at a high velocity.
He was taken by StarCare to a hospital in Lincoln where he underwent surgery to have the rebar removed.
gnat wrote: ↑Thu Jul 16, 2020 2:35 pmJust don't be like the geniuses in my welding class at Job Corps that thought it was great fun to stop a spinning angle grinder with their (gloved) hand. I'll leave the results to the imagination, but the lead asshole got what he deserved in the end and I got a good (if morbid) laugh at his expense.
Never gonna make you cry...
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
I watched part of a YouTube video years ago where some dipshit decided he was going to "overpower" the 8" chuck on his lathe with his strengthy arm. Fortunately, it just tossed him over the lathe and across the shop rather than ripping his arm off and/or pulverizing the bones...
My pop is consulting on a case where an operator's loose shirt got wrapped up in a 20-foot (!) lathe. Things didn't end well for the guy.
*edit* Not the video I was thinking of - but here's another genius.
My pop is consulting on a case where an operator's loose shirt got wrapped up in a 20-foot (!) lathe. Things didn't end well for the guy.
*edit* Not the video I was thinking of - but here's another genius.
Understeer: You will hit the wall with the front end.
Oversteer: You will hit the wall with the rear end.
Horsepower: How hard you will hit the wall.
Torque: How far you will move the wall.
Gone hunting with Alec Baldwin and Dick Cheney. Back soon.
- 32wildbilly
- Never gonna run around and desert you
- Posts: 5783
- Joined: Sat Jan 06, 2018 2:46 pm
- Location: Kneebraska
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
A future Darwin Award contestant right there.5chn3ll wrote: ↑Fri Jul 17, 2020 10:03 am I watched part of a YouTube video years ago where some dipshit decided he was going to "overpower" the 8" chuck on his lathe with his strengthy arm. Fortunately, it just tossed him over the lathe and across the shop rather than ripping his arm off and/or pulverizing the bones...
My pop is consulting on a case where an operator's loose shirt got wrapped up in a 20-foot (!) lathe. Things didn't end well for the guy.
*edit* Not the video I was thinking of - but here's another genius.
Never gonna make you cry...
Re: Upgraded my shitty HF welder with an incrementally less shitty HF welder
More practice today - made a "rectangular cuboid" out of 1/8" plate. Sucked incrementally less than last time with both the welder and plasma cutter...
I got tired of grinding out and filling mistakes. So I quit.
I got tired of grinding out and filling mistakes. So I quit.
Understeer: You will hit the wall with the front end.
Oversteer: You will hit the wall with the rear end.
Horsepower: How hard you will hit the wall.
Torque: How far you will move the wall.
Gone hunting with Alec Baldwin and Dick Cheney. Back soon.