Thanks man! I went ahead and bit the bullet and bought the bolt from Jim Ellis in Atlanta. I was able to find the other one in the car, but apparently, the PO removed both of them to leave room for the huge sub woofer box. My next project will be to wire up my Escort Redline
My 2002 996 "renovation" thread
- B3DAWG
- OG (First 100 Outposters!)
- Posts: 1659
- Joined: Sun Jan 07, 2018 11:46 am
- Location: Gawga DAWG Country
Re: My 2002 996 "renovation" thread
Last edited by B3DAWG on Tue Sep 01, 2020 11:17 am, edited 1 time in total.
- B3DAWG
- OG (First 100 Outposters!)
- Posts: 1659
- Joined: Sun Jan 07, 2018 11:46 am
- Location: Gawga DAWG Country
Re: My 2002 996 "renovation" thread
dporto gave me some good advice. If you have frunk sensor going bad and dash light on, unhook the sensor in the frunk. I did that, and waaa laaa... it worked. This also saves you from draining the battery due to the frunk light remaining on.
- Dgi 07
- OG (First 100 Outposters!)
- Posts: 218
- Joined: Mon Jan 29, 2018 7:30 am
- Location: People's Republic of New Jersey
Re: My 2002 996 "renovation" thread
- B3DAWG
- OG (First 100 Outposters!)
- Posts: 1659
- Joined: Sun Jan 07, 2018 11:46 am
- Location: Gawga DAWG Country
Re: GRAPHITE POWDER ONCE!
Re: My 2002 996 "renovation" thread
Agreed on both counts. Somehow, my case will ALWAYS be that tenth case.
Understeer: You will hit the wall with the front end.
Oversteer: You will hit the wall with the rear end.
Horsepower: How hard you will hit the wall.
Torque: How far you will move the wall.
Gone hunting with Alec Baldwin and Dick Cheney. Back soon.
Re: My 2002 996 "renovation" thread
b3freak wrote: ↑Tue Apr 03, 2018 5:11 amCoooool... I went to Home Depot to get some Sno-Seal, but they only sell it online. ugh. But thanks for the advice. And yea, I'm taking a pause and enjoy what I have ... it sure is easy to dump a fortune in these cars. Fortunately, (forgive the word redundancy), the engine doesn't have any leaks or tell tale signs of trouble. Hooked up the scanner and she has a clean bill of heath at the moment.SealGrauWailer wrote: ↑Sat Mar 31, 2018 4:19 pm yuk yuk The sno-seal has an uncanny ability to soften up worn bolsters, and it lasts too. I'll treat mine again next month when it's hot. The dye is a helpful tip though, thanks for sharing. Is your car about done in terms of heavy lifting? It sure seems to be turning into a 'good one'.
Drove the 996 to work today. Got here early! hehehe
Maybe it's me being a little over attentive while driving, but does it seem like every car on the road seems to want to race and... "get in front of the Porsche"?
EVERY driver wants to beat the guy in the Porsche........ Especially the ones that drive the base V8 Hemi Chargers that make 365hp weigh in at 4200 lbs and have 3 additional passengers in the car with them.....
William-
Current Ridez:
87' Dodge Conquest TSi
88' BMW 635CSi
89' Merkur XR4Ti
90' Mitsubishi 3000GT VR-4
95' BMW M3
99' BMW 328i Sedan
00' BMW 528i Sedan
00' Pontiac Fire Hawk Trans-Am
01' Audi S4 Twin Turbo
02' Porsche 911 Carrera
08' BMW 335i Coupe
14’ Mercedes Benz E350 Sport
Current Ridez:
87' Dodge Conquest TSi
88' BMW 635CSi
89' Merkur XR4Ti
90' Mitsubishi 3000GT VR-4
95' BMW M3
99' BMW 328i Sedan
00' BMW 528i Sedan
00' Pontiac Fire Hawk Trans-Am
01' Audi S4 Twin Turbo
02' Porsche 911 Carrera
08' BMW 335i Coupe
14’ Mercedes Benz E350 Sport
- B3DAWG
- OG (First 100 Outposters!)
- Posts: 1659
- Joined: Sun Jan 07, 2018 11:46 am
- Location: Gawga DAWG Country
Re: My 2002 996 "renovation" thread
That actually happened to me last week. Drove the 996 to work and on the way home, I'm just cruising down the road minding my own business. I pass a new Challenger like he was sitting still. That must have caused him to spill his drink or something.... or like hit him it in the nuts, cause he quickly zoomed out and came at me like a bat out of hell. You'd think I shot him a bird or something. Did I race him? Nope. Just made passing me a little difficult, then let him go by. I later caught up to him at a red light. hahaha! Oh lawd. Some people.Black-Out wrote: ↑Sat Apr 14, 2018 6:50 pmb3freak wrote: ↑Tue Apr 03, 2018 5:11 am Coooool... I went to Home Depot to get some Sno-Seal, but they only sell it online. ugh. But thanks for the advice. And yea, I'm taking a pause and enjoy what I have ... it sure is easy to dump a fortune in these cars. Fortunately, (forgive the word redundancy), the engine doesn't have any leaks or tell tale signs of trouble. Hooked up the scanner and she has a clean bill of heath at the moment.
Drove the 996 to work today. Got here early! hehehe
Maybe it's me being a little over attentive while driving, but does it seem like every car on the road seems to want to race and... "get in front of the Porsche"?
EVERY driver wants to beat the guy in the Porsche........ Especially the ones that drive the base V8 Hemi Chargers that make 365hp weigh in at 4200 lbs and have 3 additional passengers in the car with them.....
Re: My 2002 996 "renovation" thread
Bruh these Dodge dudes are all out of hand since they released the Hell Cat and the Demon. Don't get me wrong. I love the cars. I think they're kick-ass. But now, it's like everyone who owns a more basic version thinks they're Big Daddy Don Garlits at the strip or they're Dominic Toretto on the street.... Never mind that physics says a 365hp 4450lbs ANYTHING wouldn't be faster than a 320hp 2904lbs 996...... I just let them keep right on going. They don't need to see the old me come out.....lol
William-
Current Ridez:
87' Dodge Conquest TSi
88' BMW 635CSi
89' Merkur XR4Ti
90' Mitsubishi 3000GT VR-4
95' BMW M3
99' BMW 328i Sedan
00' BMW 528i Sedan
00' Pontiac Fire Hawk Trans-Am
01' Audi S4 Twin Turbo
02' Porsche 911 Carrera
08' BMW 335i Coupe
14’ Mercedes Benz E350 Sport
Current Ridez:
87' Dodge Conquest TSi
88' BMW 635CSi
89' Merkur XR4Ti
90' Mitsubishi 3000GT VR-4
95' BMW M3
99' BMW 328i Sedan
00' BMW 528i Sedan
00' Pontiac Fire Hawk Trans-Am
01' Audi S4 Twin Turbo
02' Porsche 911 Carrera
08' BMW 335i Coupe
14’ Mercedes Benz E350 Sport
- B3DAWG
- OG (First 100 Outposters!)
- Posts: 1659
- Joined: Sun Jan 07, 2018 11:46 am
- Location: Gawga DAWG Country
Re: **UPDATE** April 16
Started my weekend project(s) with repainting a little part on the door. It's been a little thorn in my side. The previous owner must have used this storage area alot because the paint was scratched off... maybe from rings or finger nails????
Taped and sanded the little sucker...
Painted with silver paint... Waaa laaaa..
Now, to the main event. I've been wanting to get my Escort Redline installed for some time now, but put it off for other projects. I prefer the Escort smart cord (see pics) instead of direct power. This cable allows you to control the main unit. Much easier than trying to fool with the detector going down the road. The Escorts make a low gruntin' type of sound which is useful for cutting through ambient noise, but it drives my wife bonkers and so have a mute button is golden.
Here are the pieces. I'm about to mount a bolt inside the Escort smart cord for mount in the center cubby.
Drilled a small hole near the center of the lower section of the unit.
Taped over the circuit board to prevent shorting out the unit.
Mounted the control unit to the center cubby...
Drilled a hole in the back to feed the power cables for the Redline unit and 12V/ground connections.
Located the Porsche cell phone plug behind the lower center console.
Tapped into the 12V switched power and ground for the radar detector's smart cord.
Connections:
Brown - ground
Yellow/Black - phone mute signal
Green/Black - Switched 12V
Red/Green - Constant 12V
Ran the cable under the dash, up the side of the door trim, up the A-pillar, and over the front head liner to the mounting point...
Turned the car on and checked. Smart cord works and Redline fires up as normal. Yay!
Taped and sanded the little sucker...
Painted with silver paint... Waaa laaaa..
Now, to the main event. I've been wanting to get my Escort Redline installed for some time now, but put it off for other projects. I prefer the Escort smart cord (see pics) instead of direct power. This cable allows you to control the main unit. Much easier than trying to fool with the detector going down the road. The Escorts make a low gruntin' type of sound which is useful for cutting through ambient noise, but it drives my wife bonkers and so have a mute button is golden.
Here are the pieces. I'm about to mount a bolt inside the Escort smart cord for mount in the center cubby.
Drilled a small hole near the center of the lower section of the unit.
Taped over the circuit board to prevent shorting out the unit.
Mounted the control unit to the center cubby...
Drilled a hole in the back to feed the power cables for the Redline unit and 12V/ground connections.
Located the Porsche cell phone plug behind the lower center console.
Tapped into the 12V switched power and ground for the radar detector's smart cord.
Connections:
Brown - ground
Yellow/Black - phone mute signal
Green/Black - Switched 12V
Red/Green - Constant 12V
Ran the cable under the dash, up the side of the door trim, up the A-pillar, and over the front head liner to the mounting point...
Turned the car on and checked. Smart cord works and Redline fires up as normal. Yay!
Last edited by B3DAWG on Mon Apr 16, 2018 5:52 pm, edited 2 times in total.
- B3DAWG
- OG (First 100 Outposters!)
- Posts: 1659
- Joined: Sun Jan 07, 2018 11:46 am
- Location: Gawga DAWG Country
Re: Against my wife's wishes...
Went against my wife's wishes, but I didn't like the faux carbon fiber stick-ons over the air vents on the dash. For some reason my wife liked them. Our compromise? Leave the faux carbon fiber overlays on the door arm rests. (which personally I think looks the best out of all the ones that were put on the car). There's one left on the dash around the hazard light switch. She doesn't want me to remove it. Ugh... it will be gone in the night! ha!
Fortunately, with much patience, I removed the two pieces without pulling off the soft-touch grey paint. Success!
Fortunately, with much patience, I removed the two pieces without pulling off the soft-touch grey paint. Success!
Last edited by B3DAWG on Mon Apr 16, 2018 6:29 am, edited 1 time in total.